Metal Stamping Archives - AUTOMATION INSIGHTS

Supply chain and labor shortages are putting extra pressure on automation solutions to keep manufacturing lines running. Even though sensors are designed to work in harsh environments, one good knock can put a sensor out of alignment or even out of condition. Keep reading for tips on ways to protect photoelectric and capacitive sensors.

Mounting solutions for photoelectric sensors

Photoelectric sensors are sensitive to environmental factors that can cloud their view, like dust, debris, and splashing liquids, or damage them with physical impact. One of the best things to do from the beginning is to protect them by mounting them in locations that keep them out of harm’s way. Adjustable mounting solutions make it easier to set up sensors a little further away from the action. Mounts that can be adjusted on three axes like ball joints or rod-and-mount combinations should lock firmly into position so that vibration or weight will not cause sensors to move out of alignment. And mounting materials like stainless steel or plastic can be chosen to meet factors like temperature, accessibility, susceptibility to impact, and contact with other materials.

When using retroreflective sensors, reflectors and reflective foils need similar attention. Consider whether the application involves heat or chemicals that might contact reflectors. Reflectors come in versions, especially for use with red, white, infrared, and laser lights, or especially for polarized or non-polarized light. And there are mounting solutions for reflectors as well.

Considering the material and design of capacitive sensors

Capacitive sensors must also be protected based on their working environment, the material they detect, and where they are installed. Particularly, is the sensor in contact with the material it is sensing or not?

If there is contact, pay special attention to the sensor’s material and design. Foods, beverages, chemicals, viscous substances, powders, or bulk materials can degrade a sensor constructed of the wrong material. And to switch perspectives, a sensor can affect the quality of the material it contacts, like changing the taste of a food product. If resistance to chemicals is needed, housings made of stainless steel, PTFE, and PEEK are available.

While the sensor’s material is important to its functionality, the physical design of the sensor is also important. A working environment can involve washdown processes or hygienic requirements. If that is the case, the sensor’s design should allow water and cleaning agents to easily run off, while hygienic requirements demand that the sensor not have gaps or crevices where material may accumulate and harbor bacteria. Consider capacitive sensors that hold FDA, Ecolab, and CIP certifications to work safely in these conditions.

Non-contact capacitive sensors can have their own special set of requirements. They can detect material through the walls of a tank, depending on the tank wall’s material type and thickness. Plastic walls and non-metallic packaging present a smaller challenge. Different housing styles – flat cylindrical, discs, and block styles – have different sensing capabilities.

Newer capacitive technology is designed as an adhesive tape to measure the material inside a tank or vessel continuously. Available with stainless steel, plastic, or PTFF housing, it works particularly well when there is little space available to detect through a plastic or glass wall of 8mm or less. When installing the tape, the user can cut it with scissors to adjust the length.

Whatever the setting, environmental factors and installation factors can affect the functionality of photoelectric and capacitive sensors, sometimes bringing them to an untimely end. Details like mounting systems and sensor materials may not be the first requirements you look for, but they are important features that can extend the life of your sensors.

If you have ever walked through a stamping department at a metal forming facility, you have heard the rhythmic sound of the press stamping out parts, thump, thump. The stamping department is the heart manufacturing facility, and the noise you hear is the heartbeat of the plant. If it stops, the whole plant comes to a halt. With increasing demands for higher production rates, less downtime, and reduction in bad parts, stamping departments are under ever-increasing pressure to optimize the press department through die protection and error-proofing programs.

The die-protection risk assessment team

The first step in implementing or optimizing a die protection program is to perform a die-protection risk assessment. This is much like risk assessments conducted for safety applications, except they are done for each die set. To do this, build a team of people from various positions in the press department like tool makers, operators, and set-up teams.

Once this team is formed, they can help identify any incidents that could occur during the stamping operations for each die set and determine the likelihood and the severity of possible harm. With this information, they can identify which events have a higher risk/severity and determine what additional measures they should implement to prevent these incidents. An audit is possible even if there are already some die protection sensors in place to determine if there are more that should be added and verify the ones in place are appropriate and effective.

The top 4 die processes to check

The majority of quality and die protection problems occur in one of these three areas: material feed, material progression, and part- and slug-out detections. It’s important to monitor these areas carefully with various sensor technologies.

Material feed

Material feed is perhaps the most critical area to monitor. You need to ensure the material is in the press, in the correct location, and feeding properly before cycling the press. The material could be feeding as a steel blank, or it could come off a roll of steel. Several errors can prevent the material from advancing to the next stage or out of the press: the feed can slip, the stock material feeding in can buckle, or scrap can fail to drop and block the strip from advancing, to name a few. Inductive proximity sensors, which detect iron-based metals at short distances, are commonly used to check material feeds.

Material progression

Material progression is the next area to monitor. When using a progressive die, you will want to monitor the stripper to make sure it is functioning and the material is moving through the die properly. With a transfer die, you want to make sure the sheet of material is nesting correctly before cycling the press. Inductive proximity sensors are the most common sensor used in these applications, as well.

Here is an example of using two inductive proximity sensors to determine if the part is feeding properly or if there is a short or long feed. In this application, both proximity sensors must detect the edge of the metal. If the alignment is off by just a few millimeters, one sensor won’t detect the metal. You can use this information to prevent the press from cycling to the next step.

Short feed, long feed, perfect alignment

Part-out detection

The third critical area that stamping departments typically monitor is part-out detection, which makes sure the finished part has come out of the stamping

area after the cycle is complete. Cycling the press and closing the tooling on a formed part that failed to eject can result in a number of undesirable events, like blowing out an entire die section or sending metal shards flying into the room. Optical sensors are typically used to check for part-out, though the type of photoelectric needed depends on the situation. If the part consistently comes out of the press at the same position every time, a through-beam photo-eye would be a good choice. If the part is falling at different angles and locations, you might choose a non-safety rated light grid.

Slug-ejection detection

The last event to monitor is slug ejection. A slug is a piece of scrap metal punched out of the material. For example, if you needed to punch some holes in metal, the slug would be the center part that is knocked out. You need to verify that the scrap has exited the press before the next cycle. Sometimes the scrap will stick together and fail to exit the die with each stroke. Failure to make sure the scrap material leaves the die could affect product quality or cause significant damage to the press, die, or both. Various sensor types can ensure proper scrap ejection and prevent crashes. The picture below shows a die with inductive ring sensors mounted in it to detect slugs as they fall out of the die.

Just like it is important to get regular checkups at the doctor, performing regular die-protection assessments can help you make continuous improvements that can increase production rates and reduce downtime. Material feed, material progression, part-out and slug-out detection are the first steps to optimize, but you can expand your assessments to include areas like auxiliary equipment. You can also consider smart factory solutions like intelligent sensors, condition monitoring, and diagnostics over networks to give you more data for preventative maintenance or more advanced error-proofing. The key to a successful program is to assemble the right team, start with the critical areas listed above, and learn about new technologies and concepts that are becoming available to help you plan ways to improve your stamping processes.